Browse Category: Suzuki GT 380

Engine Teardown

Step 1, removal of cylinder head:

As always on my blog, click on the images for a more close up detailed view.

 

 

Remove all 12 nuts from the cylinder head. Use a rubber hammer to knock it loose.

 

Bottom side of the cylinder head.

 

Step 2, removal of cylinders:

Remove the nuts holding the cylinder.  Four of them for each cylinder, see the yellow arrow.

The cylinders should come off quite easy. Three individual ones, not one big block as on the GT750.

 

Step 3, removal of clutch :

Give the wrench a tap and the bolts should come loose.

Put all the parts together in a safe location so you know where to find them later on.

Remove the axle part

 

The big nut in the middle can be hard to get off. You somehow have to lock the clutch from spinning too. And of course, bend the lock washer straight before you start.

You can buy a tool for this, but I made my own using the rusty part from the clutch. Drilled 3 mm holes and screwed the fiber and metal discs together and put them back into the clutch house.

Like this:

 

 

Locked the crank using an extra key and…..hmm, off it went, Phuu !

Keep track of the parts for the assembly process to come later.

 

Step 4, more parts to be removed:

 

Front sprocket:

 

Step 5, loosen the crank :

Block the crank using two wooden sticks.
That nut was really hard to remove. Had to use a butane/propane torch and heat up before it came loose.

Keep track of all the parts !

 

Step 6, rotor removal:

Remove the 8mm axle holding the rotor in place.

 

Suzuki recommend in the service manual to use a special tool to pull off the rotor. I don’t have that tool and made therefore another type of tool using my lathe. I have also heard some concerns about the Suzuki tool causing damages on the 8mm threads at the end of the crank.  Using an 8mm insert as shown in the picture might therefore be a better option.

Any inserts can be used as long as they have 8mm threads.

The bolt to push on the insert causing the rotor to be pulled off must be 10mm fine pitch. I took one of the bolts made for the GT750 exhaust clamping at the rear.

And off it goes 🙂

 

Step 6, splitting the crankcase:

As always, it’s a good idea to store all removed bolts on a cardboard, a simple drawing showing the placements. Since we have entered 2019 I took it one step further and printed out an image of the top and bottom side and stamped it to the cardboard plate. Easy to keep track of all the bolts.

9 bolts on the top side and 18 on the bottom side.

 

Important : In addition to the bolts on top and bottom you have to remove this three screws since they clamp the top and bottom side together. They are hard to get loose. Probably fastened with loctite glue. I had to use the butane torch and a impact driver. Don’t try without using the impact driver.

A gentle touch using a rubber hammer will get it loose.

 

 

All open…

First impression: could have been worse….

The crank needs rebuilding, but the gears looks good.

 

Step 7, removing parts:

 

Again, use the propane/butane torch to heat up and knock on the impactdriver to get the screws loose.

And keep track of the parts.

Take care, the parts will fly away when retracted. Not easy to put together again. I did the same on my GT750 and hopefully it’s all described on my blog how to do it … 🙂

Don’t miss this part while removing the crank.

 

 

And this:

 

Stored in boxes for later inspection.

 

Use a pipe to drive out the needle bearing

After a proper cleaning the crankcase will be powder blasted, but not today.

Teardown

The work to take apart the GT380 J/K model has started.

Day 1:

Aiming for a full teardown and rebuild.A lot of work to be done, but that was part of the plan. Learning by doing…and hope the result will look good.

 

Step 1, get going: 

 

The pipes are mounted wrong, off they go.

Wrong

 

Correct

 

The  old wiring is just horrible…. Luckily, I got hold of brand new wiring loom, phuu 🙂

 

Step 2, air filter and carbs:

Service manual says: Remove the left carb before removing the air filter, and I did so:

 

Dismounted the carburetors and laid them in a box for later rebuild

Step 3, organize :

Will use plastic boxes and bags to organize the parts. + stickers in the bags telling what it is.

Day 2:

Do some thinking before acting…..

Step 1:

Thinking done, loose and remove  no1 and no  2 bolts.

 

Step 2:

Since the engine is only connected to the no 3 bolt the engine can be lifted to allow a wooden board to slide in.

Step 3:

Remove  no 3 bolt.

Lift the engine to and align using a piece of wood in the left hand side until the board is even with the bench.

 

Lower the MC lifter and bolt the board to the bench.

 

Step 4:

Continue to lower the lifter until the engine can move freely away from the brackets.

Slide the engine onto the bench and you are done. 🙂 🙂